How to Build a Workbench: 6 DIY Plans for Beginners

For those of you interested in woodworking projects and have been doing it for some time, you know the struggle of working on a wobbly shop table and not getting much done.

As important as tools are for doing woodwork, you’ll eventually realize how much you need a sturdy workbench. But most workbenches in the markets are overpriced. Besides, why buy one when you can make one yourself?

Most of the workbench designs out there are too complicated. Ironically, you might end up needing another workbench to build it! But don’t worry because we’ve gathered a list of the best and simplest designs for you.

If you’re a beginner at woodwork, these 6 DIY plans on how to build a workbench might just be what you need.

1. Basic Workbench Idea

Anyone starting on woodwork needs one of these. The tools you'll need for this are a circular saw, wrench, a belt sander, a drill, and measure tape. And, the materials you'll need are- 2x8 inch lumber, 2x4 inch lumber, some plywood, carriage bolts, and 3-inch wooden screws.

Basic-Workbench-Idea

Usually, the plywood used for basic benches is ½ inch x 8 ft in size. Firstly, you should construct the four leg assemblies. Connect the ends of one leg piece with the face of the other so that they line up flush. Once wood screws are inserted, then set the legs inside the corners.

Then holes of 3/8 inch sizes should be bored through the top rails and legs. After that, you'll have to insert carriage bolts as per size from the outer of the top rails through leg pieces. It's good to install a washer and nut on each carriage bolt to tighten them. 

Secondly, you’ll need to mark up to 12 inches from the bottom of each leg. Then the rails need to be secured properly by aligning the tops with those marks. Insert the short bottom rails between the long ones.

The outside face of the bottom rail and inside face of the leg should be connected. Again, secure the short rails to the legs with screws.

Finally, you'll turn the bench upward and align the plywood top flush with the edges. Use flathead screws to secure the top. This way, you can remove it for a replacement later on.

2. Garage Workbench Idea

This type of workbench will be useful for those of you who like building things now and then. You can use either plywood or lumber for this bench, depending on how light you want the product.

Garage-Workbench-Idea

The tools for building this are brads (0.5"), decking screws (2.5"), and 1" screws for the top. For the frame, you'll need a 2"x4" and 1.5" by 3" dimension lumber. Inner cross pieces of 6x21", legs of 6x37" and hardboard of 2'x2'x4' are needed for a smooth surface. 

You first have to set the legs so that everything is square. Use a screw for this. From the bottom, set the rear crossbar 14inches far and screw each joint by rotating the structure sideways. After this, you have to set it upright to check if it's level. Adjust the legs accordingly if needed.

Since this is a garage bench, two layers of OSB or plywood should be used for the top. The hardboard is tacked onto it after. After this, you can easily add a shelf to it if you want. This type of workbench will allow for more storage comparatively.

3. Apartment Workbench Idea

No apartment is complete without a workbench; that’s even truer for DIYers. But a big bulky bench is unsightly and not suited for the tiny apartments nowadays. So, for this type of bench, you'll need to plan it out and keep everything simple.

Apartment-Workbench-Idea

Cedarwood is very good to use for this type of project as it has a nice scent to it. Invest in one of the best moisture meters for wood as well before building this. If you want a bench that’ll last and not rot away, it’s best to check the wood’s moisture content and such beforehand.

The easiest way to do this is to assemble each side first and then screw them together properly. Put the board across the top to make the working surface. There should be scope for an overhang, and you can install modular parts too. The modular section should be on caster wheels to allow mobility.

You can screw jar lids to the bottom of the modular section to create room for storage. Remember, the modular section will work as a lid to cover the extra storage parts while being a work surface.

At a suitable part of the bench, you can make a magnetic tool hanger. All you need to do is screw a flat metal bar to the wood and line up bar magnets on it. You can hang your small tools a bit from the top while heavier ones should be near to the bottom.

4. Easy-Built Workbench Idea 

If you are the type to look for an easy way out everywhere, this plan might be best for you. For this build, you'll need- 2x6 wood boards (6' cross beams), leg pieces (30"), leg braces (2'), plywood (3/4"), particleboard (3/8"), deck screws, and bolts.

Easy-Built-Workbench-Idea

It's good if you can get tabletops with half-foot longer dimensions than the cross beams and leg braces since it'll give space for making an overhang. You’ll also need some wood glue to put the pieces together.

The second step in this plan is to assemble the legs. You need to align the legs properly with the leg brace so that the braces extend 2 inches past it. Attach the pieces securely with bolts and repeat at the bottom part of the legs.

Then you'll need to attach the cross beams. Attach the cross beams to each leg assembly. The length of the beams will define the distance between the outer legs. It's good to place the middle leg about 20 inches far from the right one.

Rest the beams on top of the braces and attach them with three screws. The back cross beam should be secured outside of the back leg assemblies. 

Finally, you can just secure your tabletop with deck screws. The plywood would be your tabletop, while the particle board should be glued to it after. You can insert two more screws through the tabletop into each leg brace. And you’re done!

5. Closet Workbench Idea  

If space is a major issue and fitting a workbench in your room is too difficult, we suggest you try building this on your own. The best thing about this closet bench is that you can use parts from your old bench and incorporate them here.

Closet-Workbench-Idea

You'll need to begin by framing your closet wall by putting 2x4" planks into studs around the wall. For stability, add some cross bracing. Using drywall screws is best for this step.

The second step would be to prepare the top. There's honestly no hassle here. You can use any sort of sturdy wood of your choice, but we recommend some OSB. The size should be according to your available closet space.

Attach them with screws and make a front piece for the bench. Just use some plywood to make the front, and your bench is ready to use.

If you need some extra storage, you can always put up a pegboard for your tools. From saws to a wood lathe for beginners; you can store everything easily in a compact space with this built-in closet bench. This is very easy to make and also space-friendly. What better can a workbench offer, right?

6. Collapsible Workbench Idea

Do you want something sturdy to work on and is easily moveable? Then this design will probably fit your taste. A collapsible workbench might be the best woodworking bench ever.

The best thing about collapsible workbenches is that they can be taken apart and put together in minutes without trouble. So let’s get to the plan.

For this project, you'll need-

  • Four 2”x8”x10’
  • One 2”x8”x8’
  • One 2”x6”x8’
  • 16 lag screws of ¼” x 2 ½” size
  • 16 washers of ¼” size
  • wood glue or nails

For this project, you'll need to make sure all your wood pieces are precisely cut and accurate in size. Once you’ve got everything cut and set properly with glue.

You can put screws in. Then you need to notch the bottom stretches so that they fit in the legs well. Once the stretchers are fitted and attached to the legs, the base will be complete.

The final step is just to attach the top. You can use double layers of plywood or OSB for this. Gluing the top will make it tightly attached. Or you can screw the table from the bottom up.

This design can be taken apart easily. You just take apart the lag screws, and it breaks down into a flat pack workbench magically. And if you’re still not satisfied with these designs, you can get yourself a nice router table by checking out some of the router table reviews from different sources.

Final Words  

Nothing puts one in the mood for work than a proper workbench. And no matter what your situation is, these 6 DIY Plans for Workbenches for beginners can help you to work everything out easily.

Check Also

How to Apply Spar Varnish? A to Z Guideline

You are quite done with your woodwork project – maybe a fine piece of furniture …

Leave a Reply

Your email address will not be published. Required fields are marked *